Vacuubrand PC 3012 VARIO Manuel d'utilisateur Page 50
- Page / 75
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Documents are only to be used and distributed completely and unchanged. It is strictly the users’ responsibility to check carefully
the validity of this document with respect to his product. Manual-no.: 999164 / 19/05/2009
page 50 of 75
External pressure transducer VSK 3000,
capacitive, ceramic diaphragm sensor 1080-0.1 mbar ..................................................................636657
Coolant valve VKW-B, 24 V= ....................................................................................................674220
Venting valve VBM-B / KF 16, 24 V= ...........................................................................................674217
Y-type adapter VACUU•BUS .......................................................................................................636656
Extension cable VACUU•BUS, 2m .............................................................................................. 612552
Wall bushing VACUU•BUS ..........................................................................................................636153
Cable RS 232C, 9-pole, Sub-D .....................................................................................................637837
Installation set CVC 3000 (clips and screws) ..............................................................................636593
Level sensor (control of liquid level in catchpots, only for PC 3002/3003/3004 VARIO) ..............699908
Exhaust waste vapour condenser Peltronic .............................................................................699905
Silencer (with connection hose)....................................................................................................636588
Accessories
Ways to connect NT VARIO chemistry diaphragm pumps:
Small ange KF DN 16, with hose - for installation at hose nozzle..............................................677058
Small ange KF DN 16, for assembly directly at the valve head .................................................699918
(at inlet of ME 4C NT VARIO / MD 4C NT VARIO;
at outlet of ME 4C NT VARIO / MZ 2C NT VARIO)
Small ange KF DN 16, for assembly directly at the valve head .................................................699919
(at outlet of MD 4C NT VARIO)
Adapter to PTFE tubing DN 10/8 mm, for assembly directly at the valve head..........................636274
(at inlet of ME 4C NT VARIO / MD 4C NT;
at outlet of ME 4C NT VARIO / MZ 2C NT VARIO)
Adapter to PTFE tubing DN 10/8 mm, for assembly directly at the valve head..........................636275
(at inlet of MZ 2C NT VARIO; at outlet of MD 4C NT VARIO)
Elbow connecting piece (90°) for PTFE tubing DN 10/8 mm....................................................638434
T-piece for PTFE tubing DN 10/8 mm ........................................................................................638435
PTFE tubing DN 10/8 mm (sold by meter) ................................................................................... 638644
Attention: Dust-laden gases, deposits and condensed solvent vapour can restrict air ow out the si-
lencer. The resultant back pressure can lead to damage of pump bearings, diaphragms, and valves.
Under those conditions, a silencer must not be used.
Cleaning the pressure transducer
➨ Attention: Never use a spiky or sharp-edged tool to clean the pressure
transducer.
➨ Never touch the ceramic diaphragm of the pressure transducer with hard
objects.
➨ Fill the measurement chamber with a solvent (e. g. benzene) and allow suf-
cient cleaning time. Observe all regulations concerning usage and disposal of
solvents!
➨ Drain the solvent and dispose of in accordance with regulations, repeat cleaning
if necessary.
➨ Rinse the measurement chamber several times with alcohol in order to remove
all solvent residues.
➨ Allow the pressure transducer to dry.
➨ Readjust the pressure transducer if necessary.
Readjustment of the controller CVC 3000
See section ”Readjustment of CVC 3000”
NOTICE
- Reset / Language selection 3
- 1 switch off 3
- 2 press both 3
- Contents 4
- Safety information! 5
- Ambient conditions 6
- Operating conditions 7
- Safety during operation 7
- Maintenance and repair 9
- Technical data 10
- MV 10C VARIO-B 12
- PC 3010 VARIO 12
- MD 12C VARIO-B 12
- PC 3012 VARIO 12
- Wetted parts 14
- Components Wetted materials 14
- ME 4C NT VARIO 15
- Pump parts 15
- Position Component 15
- MD 4C NT VARIO 16
- MZ 2C NT VARIO 16
- PC 3002 VARIO 17
- Rear side CVC 3000 19
- Use and operation 20
- During operation 22
- Shutdown 25
- Vacuum Controller CVC 3000 26
- 1013 . 2 27
- Menu guide 29
- Function Pump down 30
- Function Vac control 32
- Function Auto mode 34
- Function Program 35
- Example for use 36
- Function VACUULAN 37
- Examples for use 38
- Function Conguration 40
- 1013 mbar 41
- 0...20 mbar 41
- Readjustment of CVC 3000 41
- Interface parameters 42
- Calibration in the factory 42
- Read commands ”CVC 2000” 43
- Write commands ”CVC 2000” 44
- Connection plug arrangement 44
- Description 47
- Response 47
- Operation Command 47
- Read commands ”CVC 3000” 47
- Parameter 48
- Operation 48
- Write commands ”CVC 3000” 48
- Accessories 50
- VACUUBRAND-valve with diode 51
- VACUU•BUS plug 51
- Troubleshooting 52
- Fault Possible cause Remedy 53
- ME 4C NT VARIO 57
- MZ 2C NT VARIO 57
- MD 4C NT VARIO 57
- PC 3002 VARIO 57
- Replacing the diaphragm 59
- Replacing the valves 60
- •BUS cable) 63
- Assembling the pump heads 67
- Replacing the device fuse 70
Produits connexes et manuels pour Pompes Vacuubrand PC 3012 VARIO
(12 pages)
Pompes Vacuubrand MV 10 Manuel d'utilisateur
(51 pages)
(51 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.412 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels